IAQ 6000 Series Mold Resistant Coating


Availability: In stock.

Product Name Price Qty
IAQ 6000 Coating - WHITE - 5 Gallon Pail $344.24
IAQ 6100 Coating - CLEAR - 5 Gallon Pail $344.24
Add Items to Cart

Add to Wishlist Add to Compare

Quick Overview

Fiberlock's IAQ 6000 series coatings are available here in white or clear that is durable, flexible, and permeable, 100% acrylic water based mold resistant coating that contains a fungistatic agent to resists mold growth on the dry coating's surface.


IAQ 6000 series coatings hav been tested by independent and certified laboratories to prove resistance to mold growth on the surface of the coating, and has successfully passed both ASTM G-21 and ASTM D-3273 mold resistance testing with the highest scores possible. IAQ 6000 and IAQ 6100 are both recommended for use on wood, plaster, wallboard, sheetrock, concrete, masonry block, primed metal and galvanized metal. They can also be used on new structural materials during building construction.

Surface Preparation:
Warning! If you scrape, sand, or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH approved respirator to control lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protect yourself and your family by contacting the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on to www.epa.gov/lead.

Surfaces to be coated must be free of dust, mildew, mold, dirt, grease, loose paint, oil, glue size, calcimine, wax, soap and other surface contamination. Clean mold stained surfaces with Advanced Peroxide Cleaner, or use an EPA registered antimicrobial disinfectant cleaner such as IAQ 2000, IAQ 2500, ShockWave or ShockWaveRTU. Patch irregularities with vinyl patching paste or an appropriate patching compound. IAQ 6000 is self-priming over bare sheetrock, composition board, ceiling tile and concrete.

WALLBOARD, SHEETROCK, GYPSUM BOARD- Joint cement should be sanded smooth, but avoid abrading the paper.
FERROUS METAL- Clean, then prime with IAQ 4000 rust inhibiting direct-to-metal primer.
WOOD- Seal knots and stains with IAQ 5000 stain-blocking primer.
MASONRY BLOCK- Apply one coat of IAQ 3000 block filler if a denser surface is desired.

Instructions for IAQ 6000 series application:
Apply IAQ 6000 or 6100 with brush, roller or airless spray equipment.
Brush: Synthetic, nylon or polyester bristle
Roller: Synthetic fiber 3/8”nap or longer
Spray Settings:
Pressure: 2000-3000 P.S.I.
Tips: .019 to .021 tips

Smooth Surfaces: 250-400 ft^2/gal
Porous Surfaces: 150-300 ft^2/gal

Product Specifications:
Solids by Weight ± 2%: 54.6%
Solids by Volume ± 2%: 39.6%
Viscosity at 70°F: 90-95 Kreb Units
Specular Gloss: 6º ± 1 @ 60º
Flash Point: Non-combustible
Shelf Life: 36 Months Min.
(Original Sealed Container)
Calculated VOC: 65 grams/liter

IAQ 6000 series coatings complies with the requirements for LEED® EQCredit 4.2, low-emitting materials: paints and coatings.

Tinting IAQ 6000 series Coating Instructions:
IAQ 6000 may be tinted to any off-white or pastel based color. Add up to 2 oz. of universal colorant per gallon. Start with 50% of the tinting formula and adjust as necessary.

Drying Times: (@ 70 - 77°F , 50% R.H.)
To Touch: 1 hour
To Recoat: 4 hours
Minimum Application Temp: 50º (10ºC)

Additional Information

Manufacturer Fiberlock
Application / Use IAQ 6000 is supplied ready to use, but can be thinned sparingly with water (up to 1/2 pint water per gallon) for proper application consistency if necessary. Apply IAQ 6000 generously and uniformly by brush, roller, or airless spray. Apply one coat of IAQ 6000 and ensure that the finished surface is properly sealed. To ensure that the finished surface is properly sealed, two-coats may be required on some porous surfaces.
Product Data Sheet - Left Click to view .PDF | Right Click and Save Link As to Download .PDF
Dilution(s) Ready to Use - DO NOT DILUTE
Approvals Not EPA regulated
Automatic Discounts Buy 2 Pails or more and receive Free Shipping
Packaging 5 Gallon Pail
pH Not available
S.D.S. Left Click to view .PDF | Right Click and Save Link As to Download .PDF
Manufacturer Link(s) Fiberlock Technologies

Compare Products

You have no items to compare.