You have no items to compare.
Features
• Special e-coating offers 3 to 6 times better corrosion resistant finish.
• Special bearings with unique grease offer more consistent viscosity at high temperatures and better water resistance for harsh environments.
• Special projection welded coil and plate offers extra durability in heavy vibration applications.
• Superior strength forged rotor, hub and armature offer superior flux and maximum torque for long life.
Installation:
1. Remove the four bearing cover screws on pump and discard.
2. Line up the clutch plate with the bearing cover screw holes with the dish side out. Secure with four flanged centering screws (M6-3CP, 3FR, 3PFR, 4FR, 5FR, 5PFR) (M8-5CP) and torque per specifications.
Do not use pump bearing cover screws.
3. Mount the coil assembly onto the clutch plate and secure with four flanged centering screws (1/4”-20x3/8”).
4. Lubricate the pump shaft with antiseize lubricant and insert the key into the pump shaft.
5. Slide the rotor and armature assembly over shaft. Be certain keyway of pump is aligned with armature keyway. Secure with flat washer and shaft screw (M8x25) and torque to specifications.
6. Connect the lead wire to the positive side of the electric circuit. Also be certain there is an adequate grounded connection to the coil assembly plate.
7. Engage and disengage the clutch to assure proper functioning. If full load is required initially from the pump, allow clutch to engage 20-50 cycles before commencing normal operation for adequate burnishing.
NOTE: Follow standard belt mounting and center distance procedures to determine drive pulley size, speed and horsepower per belt.
Available Clutch Models | Single Groove # 34960 | Dual Groove # 34965 (Not Stocked)
Pump Model ....................................... 3CP | 3CP
Clutch Grooves................................... 1 | 2
Shaft Size.............................................. 16.5 mm | 16.5 mm
Common Specifications
U.S. Measure | Metric Measure
Diameter............................................... 7” | (177.8 mm)
Belt Type............................................... A | (A)
Torque................................................... 75 ft./lbs. | (101.7 Nm)
Watts ..................................................... 44 | (44)
Amps...................................................... 3.6 | (3.6)
Power Required................................. 12 VDC | (12 VDC)
Weight................................................... 8.6 lbs. | (3.9 kg)
Dimensions.......................................... 7.0” x 2.07” | (177.8 x 52.6 mm)
• Special bearings with unique grease offer more consistent viscosity at high temperatures and better water resistance for harsh environments.
• Special projection welded coil and plate offers extra durability in heavy vibration applications.
• Superior strength forged rotor, hub and armature offer superior flux and maximum torque for long life.
Installation:
1. Remove the four bearing cover screws on pump and discard.
2. Line up the clutch plate with the bearing cover screw holes with the dish side out. Secure with four flanged centering screws (M6-3CP, 3FR, 3PFR, 4FR, 5FR, 5PFR) (M8-5CP) and torque per specifications.
Do not use pump bearing cover screws.
3. Mount the coil assembly onto the clutch plate and secure with four flanged centering screws (1/4”-20x3/8”).
4. Lubricate the pump shaft with antiseize lubricant and insert the key into the pump shaft.
5. Slide the rotor and armature assembly over shaft. Be certain keyway of pump is aligned with armature keyway. Secure with flat washer and shaft screw (M8x25) and torque to specifications.
6. Connect the lead wire to the positive side of the electric circuit. Also be certain there is an adequate grounded connection to the coil assembly plate.
7. Engage and disengage the clutch to assure proper functioning. If full load is required initially from the pump, allow clutch to engage 20-50 cycles before commencing normal operation for adequate burnishing.
NOTE: Follow standard belt mounting and center distance procedures to determine drive pulley size, speed and horsepower per belt.
Available Clutch Models | Single Groove # 34960 | Dual Groove # 34965 (Not Stocked)
Pump Model ....................................... 3CP | 3CP
Clutch Grooves................................... 1 | 2
Shaft Size.............................................. 16.5 mm | 16.5 mm
Common Specifications
U.S. Measure | Metric Measure
Diameter............................................... 7” | (177.8 mm)
Belt Type............................................... A | (A)
Torque................................................... 75 ft./lbs. | (101.7 Nm)
Watts ..................................................... 44 | (44)
Amps...................................................... 3.6 | (3.6)
Power Required................................. 12 VDC | (12 VDC)
Weight................................................... 8.6 lbs. | (3.9 kg)
Dimensions.......................................... 7.0” x 2.07” | (177.8 x 52.6 mm)
Additional Information
| SKU | CP34960 |
| Manufacturer | Cat-Pump |
| Manufacturer Link(s) |